INSTRUMENTATION QUESTIONAIRE:
1. Design and Selection of Process Control & Instrumentation System should include: Suitability,
Reliability, Quality, Accuracy, and Repeatability.
a) True
b) False
c) None
2. Sour Gas can be used in lieu of Instrument Air.
a) True
b) False
c) None
3. Accepted Field Signals are:
a) 3 – 15 psi, 4 – 20 mA, Hart & any Vendor Protocol.
b) 0 – 12 psi, 0 – 16 mA, 0 – 5V.
c) 0 – 30 psi, 0 – 20 mA, Hart.
4. Instrument & Control system (outdoor, unsheltered) shall be rated for operation for Outdoor
Temperature of:
a) 10 deg. C – 35 deg. C.
b) 0 deg. C – 30 deg. C
c) 0 deg. C – 55 deg. C
d) 10 deg. C – 55 deg. C
e) 0 deg. C – 65 deg. C
5. Downstream edge of orifice shall be Square & Sharp so they will not show a Beam of Light when
checked with an Orifice Edge Gauge.
a) True
b) False
c) None
6. Orifice Bore BETA is ratio of pipe ID and pipe OD.
a) True
b) False
c) None.
7. At what temperature is Degree Centigrade = Degree Fahrenheit
a) 32
b) 0
c) –40
d) 40
8. For temperature compensation in flow measurement with orifice, Thermowell shall be located
not less than 2 and no more than 30 pipe dia. downstream.
a) True
b) False
c) None.
9. Vane Type Flow Switches are preferred over Differential Pressure Type.
d) True
e) False
f) None.
10. Straightening Vanes are preferred over straight run piping in flow metering.
a) True
b) False
c) None
11. Rangeabilility of 10:1 is major requirement in flow measurement. Which of the following
method will be most appropriate:
a) Orifice
b) Positive Displacement
c) Turbine Meter
d) Variable Area
12. Flowmeter installation shall comply with:
a) API RPI 551
b) API RPI 531
c) API RPI 351
d) AMSI Sec. IV
13. Reflex Level Gauge is used for Interface Level application.
a) True
b) False
c) None
14. Transparent Level Gauges are used for: Acid, Caustic, Dirty, Dark Color liquid.
a) True
b) False
c) None
15. Gauge Cocks shall not be provided on gauges installed in light clean Hydrocarbons.
a) True
b) False
c) None
16. Displacement type instruments may be used for level range upto and including:
a) 1800 mm
b) 1830 mm
c) 1500 mm
d) 2200 mm
17. Differential pressure type instruments are no preferred for liquid – liquid interface
measurement.
a) True
b) False
c) None
18. Capacitance type level instruments shall be used in liquid that contain entrained gas.
a) True
b) False
c) None
19. Natural frequency & Wake frequency calculation shall not be performed on each thermowell, if
calculated Wake frequency is not equal to or not greater than 80% of thermowell natural frequency.
a) True
b) False
c) None
20. Non‐grounded Thermocouples are preferred due to quick response.
a) True
b) False
c) None
21. For grounded Thermocouples extension wire shield drain wire shall be grounded at
Thermocouple head.
a) True
b) False
c) None
22. For ungrounded Thermocouple (T/C), extension wire shield drain wire shall be grounded at
receiver instrument end to the instrument circuit ground.
a) True
b) False
c) None
23. Resistance Temperature Detector (RTD) shall be used when greater accuracy is not required.
a) True
b) False
c) None
24. For temperature measurement requiring maximum accuracy, following shall be used:
a) T/C
b) RTD – 2 wire
c) RTD – 3 wire
d) RTD – 4 wire
e) Filled System Instrument
f) Bi‐Metallic Instrument
25. PSIG – Atmos. Press. = PSIA
a) True
b) False
c) None
26. Range of Transmitter is 20 to 100. It is called:
a) Elevated range
b) Suppressed range
c) Elevated zero range
27. For viscous liquid, following orifice shall be used:
a) Concentric
b) Segmental
c) Eccentric
d) Quadrant Edge
28. Which Flowmeter is used for No Pressure Loss:
a) Orifice
b) Magnetic flowmeter
c) Rotameter
d) Positive displacement meter
29. CV of Control Valve is number of Gallons of water. A control valve pass through control valve
with 5 PSIG pressure drop:
a) True
b) False
c) None
30. Shield grounding is done at both ends of cable for analog signals.
a) True
b) False
c) None
CORRECT ANSWERS:
1 (a); 2 (b); 3 (a); 4 (e); 5 (b); 6 (b); 7 (c); 8 (b); 9 (b); 10 (b); 11 (c); 12 (a); 13 (b); 14 (a); 15 (b); 16 (c); 17
(b); 18 (b); 19 (a); 20 (b); 21 (a); 22 (a); 23 (b); 24 (d); 25 (b); 26 (b); 27 (d); 28 (b); 29 (b); 30 (b).
- ARAMCO :: CBT QA/QC – Instrumentation Inspector Qualification Guideline
- Instrumentation Inspection and Quality Control CBT 2021 Questioner - Part-04
- Top 50 Questioner Instrumentation Inspection and Quality Control CBT 2021 - Part-05
- Saudi Aramco Cbt Exam Questions and Answers
- QA/QC Inspector Question & Answer Handbooks-2021
- QA/QC E-books Category
- QAQC Questionnaires CONDUIT; CABLE TRAY; ENCLOSURES;
- QAQC Questionnaires FIELD INSTRUMENT; JUNCTION BOX; COLOR CODING; Grounding (J902)
- Instrument Piping and Tubing QAQC Questionnaires
- Instrument Air Supply QAQC Questionnaires